High performance embedded applications
Custom multi-probe field mappers
Magnetic flux leakage measurement
Pricing :
Price per unit; minimum order quantity 5 pieces; cut tape.
(prices are indicative)
In order to download this file, please complete the informations below:
First Name *
Last Name *
E-mail *
Company
Occupation * ---Business DevelopmentEducationEngineeringInformation TechnologyMarketingMedia and CommunicationOperationsQuality AssuranceResearchSales
Newsletter * ---Yes, send me your newsletterNo need to sign me to your newsletter
*Required fields
June 2018
This download contains:
Please refer to Chapter 6 of the data sheet for installation and use; in particular:
The MagVector™ MV2 is the ideal solution if you need to integrate a sophisticated magnetometer into your electronic system. A typical application would be a sensor array for a custom magnetic field-mapping system. The MV2 was developed by MPS Tech Switzerland Sàrl (formerly Sensima Technology SA) in cooperation with Metrolab. Metrolab uses the same sensor in several of its products, and is now making this technology available to electronic systems designers.
Note that, being an electronic peripheral component, the MagVector™ MV2 includes none of the amenities of a traditional magnetometer: the user must supply the micro-controller, control firmware, host interface, user interface, and, last but not least, calibration. For complete 3-axis Hall magnetometers, please see the THM1176 / TFM1186 family of instruments.
Measuring only 3x3x0.9 mm, the MagVector™ MV2 is a powerful magnetometer on a chip: three orthogonal Hall sensors measure (Bx,By,Bz); the “spinning current” technique minimises noise, offset and the Planar Hall Effect; a built-in temperature sensor permits temperature compensation; a programmable-gain amplifier provides measurement ranges from 0.1 to 30 T; and built-in ADCs and SPI (Serial Peripheral Interface) provide a digital interface in addition to an analog one.
The MV2 features a noise density of 300 nT/√Hz and an analog measurement bandwidth of 50 kHz. In digital mode, measurement rate can be traded off against ADC resolution, ranging from 0.375 to 3 kHz, and from 14 to 16 bits, respectively. It supports a supply voltage of 3.3 or 5 V. The compact 3×3 mm QFN package is completely nonmagnetic, compatible with MRI environments. Please see the Data Sheet for details.
A signal pin selects between the analog or digital interface. In analog mode, configuration options such as the measurement range are selected using control signals, whereas in digital mode all configuration parameters are transferred via SPI and stored in internal registers. Additional control signals and register bits provide fine control over the measurement process, for example the timing of the analog/digital conversion. In digital mode, multiple MV2s can be connected to a single SPI bus.
(1) MagVector MV2 is uncalibrated. (2) FDI2056 field range depends on coil area. (3) MagVector MV2 range can optionally be set to 30 T (uncalibrated). (4) Portability of MagVector MV2 depends on integrator's design. (5) A < 10'000 CHF B 10'000 CHF - 30'000 CHF C > 30'000 CHF
Pricing : 600 CHF
5 pieces
Pricing : 400 CHF
10 pieces
Pricing : 320 CHF
25 pieces
Pricing : 255 CHF
50 pieces
Pricing : 220 CHF
100 pieces
Pricing : 185 CHF
500 pieces
Pricing : 160 CHF
1000 pieces
Pricing : 140 CHF
2000 pieces
Pricing : 110 CHF
5000 pieces
Try it! We promise not to flood your inbox with advertising.
Thank you for your interest in Metrolab! Please check your mailbox for an e-mail to confirm your subscription. If you don't receive it, check your spam box. Don't hesitate to contact us if you continue to have trouble.
On our social networks
Liu Yu, R&D manager at Aoxin, shares insights on the use of MFC9046 160 mm NMR probe array for extremity MRI magnet mapping.
Compact but powerful USB instruments.
